Analog sampling: what do accuracy, sensitivity, precision, and noise mean?

This article covers the topics of sensitivity, accuracy, precision, and noise to help readers understand and improve measurement sample quality.


By Kathrin Huber, National Instruments                              Download PDF version of this article


When referring a sample for quality testing, you want to evaluate the accuracy and precision of your measurement. However, it is important to understand your oscilloscope’s sensitivity first. Sensitivity is the smallest change in an input signal that can cause the measuring device to respond. In other words, if an input signal changes by a certain amount - by a certain sensitivity - then you can see a change in the digital data. Do not confuse sensitivity with resolution and code width. The resolution defines the code width; this is the discrete level at which the instrument displays values. However, the sensitivity defines the change in voltage needed for the instrument to register a change in value. For example, an instrument with a measurement range of 10V may be able to detect signals with 1mV resolution, but the smallest detectable voltage it can measure may be 15mV. In this case, the instrument has a resolution of 1mV but a sensitivity of 15mV.

Figure 1. Sensitivity that is greater than the code width can help smooth out a noisy signal.

 

In some cases, the sensitivity is greater than the code width. At first, this may seem counterintuitive - doesn’t this mean that the voltage changes by an amount that can be displayed and yet not be registered? Yes! To understand the benefit, think about a constant DC voltage. Although it would be great if that voltage was really exactly constant with no deviations, there is always some slight variation in a signal, which is represented in figure 1. The sensitivity is denoted with red lines, and the code width is depicted as well. In this example, because the voltage is never going above the sensitivity level, it is represented by the same digital value - even

Figure 2. Once the signal crosses the sensitivity level, it is represented by a different digital value.

 

though it is greater than the code width. This is beneficial in that it does not pick up noise and more accurately represents the signal as a constant voltage. Once the signal actually starts to rise, it crosses the sensitivity level and then is represented by a different digital value, as in figure 2. Keep in mind that your measurement can never be more accurate than the sensitivity.


Figure 3. Calculating the vertical accuracy of an oscilloscope

Figure 4. Calculating the vertical accuracy of a DMM or power supply

There is also some ambiguity in how the sensitivity of an instrument is defined. At times, it can be defined as a constant amount as in the example. In this case, as soon as the input signal crosses the sensitivity level, the signal is represented by a different digital value. However, sometimes it is defined as a change in signal. After the signal has changed by the sensitivity amount specified, it is represented by a different signal. In this case, it is not the absolute voltage that matters, but rather the change in voltage. In addition, some instruments define the sensitivity as around zero.

Not only does the exact definition of the term sensitivity change from company to company, but different products at the same company may use it to mean something slightly different as well. It is important that you check your instrument specifications to see how sensitivity is defined; if it is not well-documented, contact the company for clarification. Accuracy is defined as a measure of the capability of the instrument to faithfully indicate the value of the measured signal. This term is not related to resolution; however, the accuracy can never be better than the instrument resolution. Depending on the instrument or digitizer, there are different expectations for accuracy. For instance, in general, a digital multimeter (DMM) is expected to have higher accuracy than an oscilloscope. How accuracy is calculated also changes by device; always check your instrument specifications to see how your particular instrument calculates accuracy.

Oscilloscopes define the accuracy of the horizontal and vertical system separately. The horizontal system refers to the time scale or the X axis; the horizontal system accuracy is the accuracy of the time base. The vertical system is the measured voltage or the Y axis; the vertical system accuracy is the gain and offset accuracy. Typically, the vertical system accuracy is more important than the horizontal one. The vertical accuracy is typically expressed as a percentage of the input signal and a percentage of the full scale. Some specifications break down the input signal into the vertical gain and offset accuracy. Figure 3 shows two different ways in which the accuracy might be defined. For example, an oscilloscope can define the vertical accuracy in the following manner:

Vertical Accuracy = ±2% of Input, ±1% Full Scale

With a 10V input signal and using the 20V range, you can then calculate the accuracy:

Vertical Accuracy = ±(2% of Input + 1% Full Scale)

Vertical Accuracy = ±(0.02 * 10 + .01 * 20) = ±0.4V

DMMs and power supplies usually specify accuracy as a percentage of the reading. Figure 4 shows three different ways of expressing the accuracy of a DMM or power supply.

The term ppm means parts per million. Most specifications also have multiple tables for determining accuracy. The accuracy depends on the type of measurement, the range, and the time since last calibration. Check your specifications to see how accuracy is calculated. As an example, a DMM is set to the 10V range and is operating 90 days after calibration at 23°C ±5°C, and is expecting a 7V signal. The accuracy specifications for these conditions state ±(20 ppm of reading + 6 ppm of range). You can then calculate the accuracy:

In this case, the reading should be within 200 μV of the actual input voltage. DAQ cards often define accuracy as the deviation from an ideal transfer function. Figure 5 shows an example of how a DAQ card might specify the accuracy. It then defines the individual terms: gain eror = residual AI gain error + (gain temperature coefficient * temperature change from last internal calibration) + (reference temperature coefficient * temperature change from last external calibration). Offset error = residual AI offset error + (offset temperature coefficient * temperature change from last internal calibration + INL error).

Figure 5. Calculating the accuracy of a DAQ device

The majority of these terms are defined in a table and based on the nominal range. The specifications also define the calculation for noise uncertainty. Noise uncertainty is the uncertainty of the measurement because of the effect of noise in the measurement and is factored into determining the accuracy. In addition, there may be multiple accuracy tables for your device, depending on if you are looking for the accuracy of analog in or analog out or if a filter is enabled or disabled.

Figure 6. Precision and accuracy are related but not the same.

 

Accuracy and precision are often used interchangeably, but there is a subtle difference. Precision is defined as a measure of the stability of the instrument and its capability of resulting in the same measurement over and over again for the same input signal. Whereas accuracy refers to how closely a measured value is to the actual value, precision refers to how closely individual, repeated measurements agree with each other.

Precision is most affected by noise and short-term drift on the instrument. The precision of an instrument is often not provided directly, but it must be inferred from other specifications such as the transfer ratio specification, noise, and temperature drift. However, if you have a series of measurements, you can calculate the precision.

Figure 7. Calculating precision


For instance, if you are monitoring a constant voltage of 1V, and you notice that your measured value changes by 20µV between measurements, then your measurement precision can be calculated as follows.

Typically, precision is expressed as a percentage. In this example, the precision is 99.998 percent. Precision is meaningful primarily when relative measurements (relative to a previous reading of the same value), such as device calibration, need to be taken.

Figure 8. An ideal resistor is reflected in A, but,resistors have internal thermal noise as represented in B.

 

Do not confuse sensitivity with resolution and code width. The resolution defines the code width; this is the discrete level at which the instrument displays values. However, the sensitivity defines the change in voltage needed for the instrument to register a change in value. For example, an instrument with a measurement range of 10V may be able to detect signals with 1mV resolution, but the smallest detectable voltage it can measure may be 15mV. In this case, the instrument has a resolution of 1mV but a sensitivity of 15mV.

Figure 9. Most likely source of noise

 

An ideal electronic circuit produces no noise of its own, so the output signal from the ideal circuit contains only the noise that was in the original


Related


Give Your Product a Voice with Alexa

Join us for a deep dive into the system architecture for voice-enabled products with Alexa Built-In. Device makers can use the Alexa Voice Service (AVS) to add conversational AI to a variety of produc...

The two big traps of code coverage

Code coverage is important, and improving coverage is a worthy goal. But simply chasing the percentage is not nearly so valuable as writing stable, maintainable, meaningful tests. By Arthur Hick...

Securing the smart and connected home

With the Internet of Things and Smart Home technologies, more and more devices are becoming connected and therefore can potentially become entry points for attackers to break into the system to steal,...

Accurate and fast power integrity measurements

Increasing demands on power distribution networks have resulted in smaller DC rails, as well as a proliferation of rails that ensure clean power reaches the pins of integrated circuits. Measuring r...

 

Perfect Motion Control For the Networked World

We live in a physical world where everything is connected. Trinamic transforms digital information into physical motion with accessible, flexible, and easy to use toolkits putting the world’s be...


New High-Performance Serial NAND: A Better High-Density Storage Option for Automotive Display

The automotive requirements: speed, reliability and compatibility. Winbond's high-performance serial NAND Flash technology offers both cost and performance advantages over the SPI NOR Flash typica...


President Tung-Yi talks about Winbond

Winbond is a leading specialty memory solution provider with a wide rage of product portfolio. Owned technology and innovation are our assets for our industry and our customers. Winbond we are high qu...


New Memory and Security Technologies for Designers of IoT Devices

Internet of Things (IoT) edge nodes are battery-powered, often portable, and are connected to an internet gateway or access point wirelessly. This means that the most important constraints on new I...


Winbond TrustMe Secure Flash - A Robust and Certifiable Secure Storage Solution

Winbond has introduced the TrustMe secure flash products to address the challenge of combining security with advanced process nodes and remove the barriers for adding secure non-volatile storage to pr...


Ultra-Low-Power DRAM: A “Green” Memory in IoT Devices

Winbond is offering a new way to extend the power savings available from Partial Array Self-Refresh (PASR), which was already specified in the JEDEC standard by implementing a new Deep Self-Refresh (D...


Polytronics Thermal Conductive Board (TCB) at Electronica 2018

This video introduce the basic product structure, advantage, and application of Polytronics thermal conductive board (TCB). Polytronics exhibit wide range of circuit protection products and thermal ma...


Arrow and Analog Devices strategic partnership and collaborative approach to provide solutions for our customers.

Mike Britchfield (VP for EMEA Sales) talks about why Analog Devices have a collaborative approach with Arrow Arrow’s design resources are key, from regional FAEs in the field to online des...


WE MAKE IT YOURS! Garz & Fricke to present the latest HMIs and SBCs at Electronica 2018

Sascha Ulrich, Head of Sales at Garz & Fricke, gives you a quick overview about the latest SBC, HMI and Panel-PC Highlights at electronica 2018. Learn more about the SANTOKA 15.6 Outdoor HMI, the ...


Macronix Innovations at electronica 2018

Macronix exhibited at electronica 2018 to showcase its latest innovations: 3D NAND, ArmorFlash secure memory, Ultra Low Vcc memory, and the NVM solutions with supreme quality mainly focusing on Automo...


ams CEO talks about their sensor solutions that define the mega trends of the future

In this video Alexander Everke, ams’ CEO, talks to Alix Paultre of EETimes about their optical, imaging and audio sensor solutions in fast-growing markets – from smartphones, mobile device...


Intel accelerated IoT Solutions by Arrow

Arrow is showing Intel’s Market Ready Solutions in a Retailer shop with complete eco environment. From sensors via gateways into the cloud, combined with data analytics, the full range of Intel ...


CSTAR - Manufacturers of cable assembly from Taiwan

CSTAR was founded in 2010 in Taipei, Taiwan. Through years of experience, we are experts in automotive products, LCD displays, LCD TVs, POS, computers, projectors, laptops, digital cameras, medical ca...


NXP Announces LPC5500 MCU Series

Check this video to discover the new NXP microcontroller LPC5500, the target application and focus area. Links to more information: LPC5500 Series: World’s First Arm® Cortex® -M...


Molex Meets Solutions at Electronica

These are exciting times in the electronics world as Molex migrates from a pure connectors company to an innovate solutions provider. Solutions often start at the component level, such as the connecto...


Alix Paultre investigates Bulgin's new optical fiber rugged connector range at Electronica 2018

Alix Paultre interviews Bulgin's Engineering Team Leader Christian Taylor to find out more about the company's new range of optical fiber connectors for harsh environments. As the smallest rug...


Cypress MCU and Connectivity are the best choice for real-world IoT solutions.

Cypress’ VP of Applications, Alan Hawse, explains why people should use Cypress for their IoT connectivity and MCU needs. Cypress wireless connectivity and MCU solutions work robustly and sea...


Chant Sincere unveils their latest High Speed/High Frequency connection solutions at Electronica 2018

Chant Sincere has been creating various of product families to provide comprehensive connection solutions to customers. USB Series Fakra Series QSFP Series Metric Connector Series Fibro ...


Addressing the energy challenge of IoT to unleash billions of devices

ON Semiconductor introduces various IoT use cases targeted towards smart homes/buildings, smart cities, industrial automation and medical applications on node-to-cloud platforms featuring ultra-low po...


ITECH, world leading manufacturer of power test instruments, shinned on electronica 2018

ITECH, as the leading power electronic instruments manufacturer, attended this show and brought abundant test solutions, such as automotive electronics, battery test, solar array simulator, and electr...


ITECH new series give users a fantastic user experience

ITECH latest series products have a first look at the electronics 2018, such as IT6000B regenerative power system, IT6000C bi-directional programmable DC power supply, IT6000D high power programmable ...


SOTB™ Process Technology - Energy Harvesting in Embedded Systems is Now a Reality

Exclusive SOTB technology from Renesas breaks the previous trade-off between achieving either low active current or low standby current consumption – previously you could only choose one. With S...


Power Integrations unveils their new motor control solution

In this video friend of the show Andy Smith of Power Integrations talks to Alix Paultre from Aspencore Media about their new BridgeSwitch ICs, which feature high- and low-side advanced FREDFETs (Fast ...


Panasonic talks about their automotive technology demonstrator

In this video Marco from Panasonic walks Alix Paultre of Aspencore Media through their automotive technology demonstrator at electronica 2018. The demonstrator highlights various vehicle subsystems an...